Archive for April, 2018

Performance Tracking: Efficient Fluid & Waste Management

 Closeup of drilling fluids.

If you’re not tracking the right metrics, you’re leaving money on the table!

  • – Accurately tracking waste volumes allows E&P Companies to identify and mitigate the sources of excess waste.
  • – By reducing waste volumes, companies reduce the environmental risk associated with it.
  • – E&P Companies must accept long-term liability of waste generated from operations. Proper measurement and tracking procedures help to reduce exposure to this liability.
  • – Consistently tracking and maximizing in system efficiency results in better rates of penetration and drilling fluids and solids control cost reductions.
  • – Performance tracking promotes standardization with drilling fluid and waste management operations.
  • – Aerion uses a holistic approach to quantify and track the efficiency of the entire drilling fluid and waste management system, including drilling volumes, low gravity solids content in drilling fluids, drilling fluids losses, equipment optimization and segmented waste disposal data.

Performance Tracking Approach

The primary goal of performance tracking is to consistently minimize drilling costs by using a three-pronged approach:

  1. 1. Solids control equipment performance and optimization
  2. 2. Drilling fluid volume tracking and solids analysis
  3. 3. Waste minimization, but not at the expense of higher drilling fluid costs

By tracking the performance data associated with each of these facets of the drilling process, companies gain valuable insight into their interrelatedness. The effectiveness of solids control equipment has a profound impact on the quality of drilling fluid and the amount of dilution needed to maintain it. Solids control equipment also plays an important part when it comes to managing waste volumes. Drilling fluid properties must be considered when optimizing solids control equipment and waste disposal practices, and understanding waste disposal options is necessary when determining both drilling fluid and solids control strategies. Partnering with an expert, such as Aerion, who specializes in proactively managing the entire solids control, drilling fluids and waste management systems allows operators to improve the drilling process, cut unnecessary costs and maximize profits.

Benefits of Performance Tracking

“What gets measured gets managed.”

E&P Companies have a difficult time accurately measuring the efficiency of their drilling fluid, solids control and waste management efforts. Typically, more focus is placed on measuring drilling fluid volumes than on solids control performance and waste volumes. Without proper measurement, these companies are missing out on many of these benefits.

Performance Tracking Produces Drilling Improvements

Minimizing the percentage of solids in the drilling fluid significantly impacts the speed of drilling operations. Some solids are necessary to maintain specific drilling fluid properties, but some solids, referred to as drilled solids or cuttings, act as contaminants for the drilling fluid. Minimizing their effect will increase rates of penetration and can be done by mechanically removing them from the fluid system and by adding base fluid (dilution). Knowing the amount of drill solids in the fluid system and/or the efficiency of the removal process of various solids control equipment allows for increased fluid performance. This will have significant impacts on lowering repair and maintenance costs of downhole tools and rig equipment.

Performance Tracking Allows for the Reduction of Dilution and Chemical Costs

The easiest and most common practice for reducing drill solids content is dilution. While dilution will always be necessary for drilling operations, it can be quite expensive and should be minimized. The most obvious cost associated with dilution is the price per gallon of base fluid, as well as the transportation cost. Trucking this fluid to a well site is also expensive. For every gallon of fresh base fluid that is added to the drilling fluid system, a certain amount of chemicals must also be added. Excessive dilution increases the volume of drilling fluid that must be managed, usually by sending back to a mud plant where it is reconditioned (for a price) and stored for later use.
Mechanical solids control equipment, if optimized properly, can effectively remove drill cuttings and decrease costs as it significantly reduces the amount of dilution and chemical required. It also increases the life of the mud so that it can be used much longer, which further reduces the transportation and disposal costs associated with it.

Performance Tracking Produces Accurate Waste Logs and Trucking Tickets

For decades, the standard method for calculating the volume of waste has been the “eyeball method,” which is obviously not a very accurate performance tracking technique. In a closed-loop system, the task is performed at the well site by the truck driver who always leaves with a “full load.” This waste is delivered to a waste disposal yard, where the E&P company usually pays a price based on the volume of waste that was delivered. Without a more accurate method to measure waste volumes, the E&P company usually pays to dispose of more waste than was actually delivered. Using accurate methods alone can reduce the cost of waste disposal by as much as 25-30 percent.

Performance Tracking Reduces Waste Volumes

Optimizing solids control equipment to improve solids removal efficiency reduces the amount of dilution, which directly correlates to the amount of waste volume generated.

More Dilution = More Waste.

The process flow through the solids control equipment can also have an impact on waste volumes. When solids are removed from the drilling fluid, they carry base fluid with them, which contributes to the overall waste volume. Therefore, it is not only critical to optimize the solids control equipment for solids removal efficiency, but also for producing dryer cuttings in the waste stream. Dryer cuttings also indicate that more base fluid was recovered so that it could be recycled and reused.

What a System without Performance Tracking Looks Like:

  • – Poor project P&L
  • – High cost of waste disposal
  • – High drilling fluid costs
  • – Slower ROPs and more Days on Well
  • – Fewer completed wells
  • – Underutilized Solids Control Equipment

Common Performance Tracking Methods

In most cases, performance tracking for solids control, drilling fluid and waste management relies exclusively on daily reports (mud reports) and waste trucking manifests submitted by the drilling fluid engineers and truck drivers on the wellsite location. Among other things, performance tracking techniques involve close monitoring of daily dilution rates, footage drilled and commercial solids and other chemicals that are added to the drilling fluid system.

Fluid Testing in the field is an extremely important component of performance tracking. A full “mud check” is completed and the results are submitted with the daily mud report. The mud check requires multiple tests including a retort test that determines the percentage of solids, oil and water of a specific mud sample. Mud samples can be collected at multiple locations, but are most commonly collected just before being pumped downhole. In some cases, mud samples will be sent in for more extensive testing using expensive laboratory equipment.

Solids control equipment selection is usually determined by past experience and adherence to the status quo without any analysis from performance tracking methodologies. This generally results in having both equipment underutilization and missized equipment which will show up in performance tracking as low runtime percent. The operator ends up paying for the equipment that is not properly selected and operated.

Solids control equipment settings are sometimes noted on the mud report, but rarely include enough accurate details to make useful decisions. Unfortunately, most common tracking efforts for solids control equipment don’t go much further than shaker screen sizes and centrifuge runtime hours.

Performance Tracking: How is Aerion Different?

Aerion’s most valuable assets for performance tracking are its personnel on location. Our supervisors and equipment operators have the extensive training and experience to ensure that customers receive the best possible service.

Because the solids content of the drilling fluid is such a critical piece of information for performance tracking, Aerion uses only 50 mL Gravimetric Retort Kits which are much more accurate than the standard 10 mL Retort Kits that are most often used by drilling fluid technicians. Aerion personnel at the wellsite collect mud samples at the same times and locations as the drilling fluid engineer and throughout the solids control process in order to measure the equipment performance.

Many of these samples are shipped to the Aerion Laboratory Facility for further testing. Aerion has the capability to run a full mud check as well as particle size analysis using the Microtrac S3500, which uses laser diffraction to obtain the most accurate measurements.

Aerion also analyzes waste samples from the major fluids process systems to measure the retention of drilling fluids on cuttings. This information is reviewed along with accurate waste volumes to make necessary cost savings adjustments.

Aerion has a dedicated team of analytical experts that is responsible for analyzing operational data for each well, such as solids removal efficiency, diesel consumption rates, centrifuge utilization, etc. This information is mined even further before reports are developed to give a deeper understanding of performance drivers.

Sophisticated performance tracking techniques give Aerion a large database of information that is not only used for post-well analysis, but also project planning. This information helps Aerion standardize solids control operating procedures in various shale plays with various drilling fluid systems. This level of insight gives E&P companies confidence when entering new basins or expanding their drilling programs.

Contact Aerion Today

Aerion is the leading provider of high-quality fluid processing and waste management solutions. Our dedication to measurement and performance tracking gives us an unparalleled advantage for understanding and solving our customers’ challenges by using tested strategies that increase their bottom line. To learn more about our performance tracking methods and how we can help your drilling program, contact us today.

Map

Customers across the country have come to rely upon Aerion to provide professional, safe and cost-effective oilfield services wherever and whenever needed. We invite you to contact us today to find out how our full range of oilfield services can improvie your operations